廣州南洋電纜集團有限公司
GUANGZHOU   NANYANG   CABLE  GROUP   CO.,LTD

廣州南洋電纜有限公司

銷售中心

(Tender Quatation) Sales center

500kV power cable
500kV電力電纜
500kV power cable

Rated voltage 500kV (Um=550kV) XLPE insulated corrugated aluminum PE (PVC) sheathed power cable products introduction

1 Product Implementation standards

1.1  GB/T22078.1-2008 Rated voltage of 500kV (Um=550kV) XLPE power cable and power cable accessories systems - Test methods and requirements

1.2  GB/T22078.2-2008 Rated voltage of 500kV (Um=550kV) XLPE insulated power cable

1.3  GB/T22078.3-2008 Rated voltage of 500kV (Um=550kV) XLPE insulated power cable accessories


2 The use of conditions:

2.1 Use occasions

2.1.1 The maximum allowable temperature of the cable conductor: when the normal operation is 90 degrees C; short circuit (the longest 5S) is 250.

2.1.2 The minimum bending radius of the cable is recommended to 20 times the diameter of the cable.

2.1.3 The application environment of the cable is mainly determined by the performance of the cable metal sheath and the plastic outer sheath

2.1.3.1 Metal sleeve

The lead sheath cable and the corrugated aluminum sheath cable are suitable for general occasions, especially for the following occasions:

-Lead sheathed cable: corrosion is more serious but not nitric acid, acetic acid, organic matter (such as coal) and strong alkaline corrosion, and the mechanical force (tension, pressure, vibration and other small places).

-corrugated aluminum sheath cable: corrosion is not serious and requires a certain mechanical strength of the premises (such as direct connection with the transformer, laying on the bridge and shaft medium).

2.1.3.2 Outer  sheath of plastic

-type 02 (PVC) outer sheath cable is mainly suitable for the high voltage cable line with the general fire  protection requirement and a certain insulation requirement for the outer sheath;

-type 03 (PE) outer sheathed cables are mainly suitable for high voltage cable lines with high external  insulation requirements directly buried.

2.2 Rated Voltage In Power System

Allowable rated voltage value of cable U0UUm is as follows:


Table:

U0: The rated voltage phase voltage between a conductor and a shield or a metal shield for the design of a cable.

U: Rated voltage (line voltage) between conductors used in cable design

Um: Equipment maximum voltage the maximum value of the highest voltage system using equipment


3 Cable type and description

3.1 Code


Note: Corrugated aluminum sheath including extruded corrugated aluminum sheath and welding corrugated aluminum sheath, two kinds of corrugated aluminum sheath code is LW, does not distinguish, but the welding corrugated aluminum sheath should be clear in the product name, the name of the welding corrugated aluminum sheath is extruded corrugated aluminum sheath. Corrugated copper sheath and corrugated stainless steel sheath are all welded metal sheath.


3.2 Type


3.3 Product Description


The cable model is composed of characteristic  code, insulation, conductor, metal sheath, non-metallic sheath , water blocking structure and rated voltage), specifications (core, the nominal cross-section) and  standard code.

3.3.1 Cable Specifications

The conductor cross section (mm2) of rated voltage 290/500kV cable is 800, 1000, 1200, (1400), 1600, (1800), 2000, (2200), 2500, The cable specifications in the brackets are non preferred conductor cross sections;

3.1.2 Model followed by the insulation, conductors, metal cover, non-metallic outer sheath and fire-retardant characteristics, Anti-termites , water blocking structure of the cable constitute;

3.1.2.1 ZC-YJ LW 02-Z-290/500kV-1*1600

ZC…………..…………..Flame retardant

YJ…………..……………XLPE insulated(Copper)

LW…………..………….Corrugated  aluminum sheath

02…………..…………..PVC outer sheath

Z…………..…………….longitudinal  Water blocking

290/500kV………….Voltage grade

1*1600……………….Single core and conductor nominal cross-section

Cable specification: Rate voltage 290/500kV, single core, copper conductor nominal cross section 1600mm2, XLPE insulated corrugated aluminum sheathed longitudinal blocking water flame retardant class C PVC sheathed power cable.

3.1.2.2   FY-YJ L LW 03-Z-290/500KV-1*2500

FY………Anti-termites

YJ………XLPE insulated

L………..aluminum core

LW……..Corrugated aluminum sheath

03………PE outer sheath

Z………...Longitudinal water proof

290/500KV………….Voltage grade

1*2500………Single core and conductor nominal cross-section

Cable specification: Rate voltage 290/500kV, single core, Aluminum conductor nominal cross section 2500mm2, XLPE insulated corrugated aluminum sheathed longitudinal water blocking termitproof PE  sheathed power cable.

3.1.2.3   FY-YJ L Q 03-Z-290/500KV-1*2000

FY………Anti-termites

YJ………XLPE insulated

L………..aluminum core

Q……….lead sheathed

03………PE outer sheath

Z…………Longitudinal water proof

290/500KV……Voltage grade

1*2000……Single core and conductor nominal cross-section

Cable specification: Rate voltage 290/500kV, single core, Aluminum conductor nominal cross section 2000mm2, XLPE insulated lead sheathed longitudinal water blocking termitproof PE sheathed power cable.


4 Product Structure

4.1 Product Structure Diagrams

Specification Model: YJLW03-Z-290/500KV-1*2500mm2


Specification Model: FY-YJLW03-Z-290/500KV-1*2500mm2


500kV電力電纜

額定電壓 500kV(Um=550kV)交聯聚乙烯絕緣皺紋鋁套聚(氯)乙烯護套電力電纜

一、 產品執行標準

GB/T22078.1-2008額定電壓 500kV(Um=550kV)交聯聚乙烯絕緣電力電纜及其附件電力電纜系統-試驗方法和要求

GB/T22078.2-2008額定電壓 500kV(Um=550kV)交聯聚乙烯絕緣電力電纜

GB/T22078.3-2008額定電壓 500kV(Um=550kV)交聯聚乙烯絕緣電力電纜附件


使用條件

2.1使用場合

2.1.1電纜導體最高允許溫度:正常運行時為 90℃;短路時(最長 5s)為 250℃。

2.1.2電纜的安裝最小彎曲半徑推薦為 20  倍電纜外徑。

2.1.3電纜的使用環境主要由電纜金屬套和塑料外護套的性能確定

2.1.3.1金屬套

鉛套和皺紋鋁套除適用于一般場所外,特別適用于下列場合:

—— 鉛套電纜:腐蝕較嚴重但無硝酸、醋酸、有機質(如泥煤)及強堿性腐蝕質,且受機械力(拉力、壓力、振動等)不大的的場所。

—— 皺紋鋁套電纜:腐蝕不嚴重和要求承受一定機械力的場所(如直接與變壓器連接,敷設在橋 梁上和豎井中等)。

2.1.3.2  塑料外護套    

—— 02 型(聚氯乙烯)外護套電纜主要適用于有一般防火要求和對外護套有一定絕緣要求的高壓電纜線路;

—— 03 型(聚乙烯)外護套電纜主要適用于對外護套絕緣要求較高的直埋敷設的高壓電纜線路。  如有必要用于隧道或豎井中時應采取一定的阻燃防火措施。


2.2電力系統額定電壓

電纜允許的額定電壓U0UUm值如下:

表中:

U0:電纜設計用的導體與屏蔽或金屬屏蔽之間的額定電壓(相電壓)

U:電纜設計時用的導體之間的額定電壓(線電壓)

Um:設備最高電壓(使用設備的系統最高電壓的最大值)


三、電纜型號和產品表示方法

3.1 代號表示

注: 皺紋鋁護套包括擠包皺紋鋁護套和焊接皺紋鋁護套,兩種不同皺紋鋁護套的代號均為LW不作區分,但焊接皺紋鋁護套應在產品名稱中明確,名稱中未說明焊接皺紋鋁護套的即為擠包皺紋鋁護套。皺紋銅護套和皺紋不銹鋼護套均為焊接金屬護套。


3.2 產品型號


3.3 產品表示方法


電纜型號依次由特性代號、絕緣、導體、金屬套、非金屬護套、阻水結構的代號、額定電壓)、規格(芯數、標稱截面)及標準編號表示

3.3.1 電纜規格

額定電壓290/500KV電纜的導體截面(mm2)為80010001200、(1400)、1600、(1800)、2000、(2200)、2500。其中括號內電纜規格為非優選導體截面;

3.1.2 型號依次由絕緣、導體、金屬套、非金屬護套及阻燃特性、防白蟻、阻水結構的代號構成:


3.1.2.1 ZC-YJ LW 02-Z-290/500kV-1*1600

ZC…………..…………..阻燃C類

YJ………………………..交聯聚乙烯絕緣(銅芯)

LW………….…………..皺紋鋁套

02…………..…………..聚氯乙烯護套

Z…………….…………..縱向阻水

290/500kV………….電壓等級

1*1600……….單芯電纜導體標稱截面

產品表示方法:額定電壓290/500KV、單芯、銅導體標稱截面1600mm2、交聯聚乙烯絕緣皺紋鋁套聚氯乙烯護套縱向阻水阻燃C類電力電纜


3.1.2.2   FY-YJ L LW 03-Z-290/500KV-1*2500

FY…………..…………..防白蟻

YJ…………..……………交聯聚乙烯絕緣

L…………..…………….鋁芯

LW…………..………….皺紋鋁套

03…………..…………..聚乙烯外護套

Z…………..…………….縱向阻水

290/500KV…………電壓等級

1*2500…………...單芯電纜導體標稱截面

產品表示方法:額定電壓290/500KV、單芯、鋁導體標稱截面2500mm2、交聯聚乙烯絕緣皺紋鋁套聚乙烯護套縱向阻水防白蟻電力電纜


3.1.2.3   FY-YJ L Q 03-Z-290/500KV-1*2000

FY…………..…………..防白蟻

YJ…………..……………交聯聚乙烯絕緣

L…………..…………….鋁芯

Q…………..……………鉛套

03…………..…………..聚乙烯外護套

Z…………..…………….縱向阻水

290/500KV………….電壓等級

1*2000…………....單芯電纜導體標稱截面

產品表示方法:額定電壓290/500KV、單芯、鋁導體標稱截面2000mm2、交聯聚乙烯絕緣鉛套聚乙烯護套縱向阻水防白蟻電力電纜


四、產品結構

4.1 產品結構圖

規格型號: YJLW03-Z-290/500KV-1*2500mm2


規格型號: FY-YJLW03-Z-290/500KV-1*2500mm2


4.2 產品結構

4.2.1 導體

電纜導體材料采用銅芯緊壓圓形導體或扇形分割導體。當導體標稱截面積為800mm2時,可任意選用緊壓導體或分割導體結構。1000mm2及以上導體則采用分割導體結構, 導體的表面光潔、無油污、無毛刺、銳邊以及凸起或斷裂的單線;

當電纜導體標稱截面為800mm2時,導體中的單線根數不少于53,當標稱截面為1000mm21600mm2時,電纜銅分割導體中的單線不少于170根,標稱截面為1800mm2及以上電纜銅分割導體中的單線不少于265根。


4.2.2 導體屏蔽

導體屏蔽由半導電包帶和擠出半導電層組成,其厚度近似值為2.5mm,其中擠包半導電層厚度近似值為2.0mm

屏蔽用半導電材料采用超光滑可交聯半導電材料。擠包半導電層均勻地包覆在半導電包帶外,并牢固地粘在絕緣層上。半導電層與絕緣層的交界面光滑,無明顯絞線凸紋、尖角、顆粒、燒焦或擦傷痕跡。


4.2.3 絕緣

絕緣材料采用進口超凈化可交聯聚乙烯料,絕緣平均厚度與標稱值應為正公差,其公差不大于其標稱值的10%+0.1mm


4.2.4 絕緣屏蔽

絕緣屏蔽為擠包半導電層,其厚度近似值為1.0mm。絕緣屏蔽應與導體擠包屏蔽層和絕緣層一起 三層共擠。絕緣屏蔽應均勻地包覆在絕緣表面,并牢固地粘附在絕緣層上。絕緣屏蔽的表面以及其與絕緣層的交界面應光滑,無尖角、顆粒、燒焦或擦傷的痕跡。


4.2.5 緩沖層、縱向阻水結構

緩沖層:在導體半導電屏蔽層外應有緩沖層,緩沖層可采用半導電性材料或具有縱向阻水功能的半導電阻水膨脹帶繞包而成。繞包要求平整、緊實、無皺褶。

縱向阻水結構:對電纜的金屬套內間隙有縱向阻水要求時,絕緣屏蔽與金屬套間應有縱向阻水結構。

縱向阻水結構由半導電阻水膨脹帶繞包而成,  半導電阻水帶繞包緊密、平整、無擦傷。


4.2.6 金屬屏蔽

金屬屏蔽可用銅絲編織帶、銅帶或金屬套等制作。

金屬屏蔽、金屬套截面應滿足系統短路容量的要求。當金屬套的截面不滿足要求時,必須通過增加金屬套厚度或增加銅線屏蔽等方式來滿足。


4.2.7 金屬套

金屬護套分為鉛護套和皺紋鋁護套兩種。

皺紋鋁護套采用純度不小于99.6%的鋁材制造,鋁帶的伸長率應不小于16%。焊接皺紋鋁護套焊縫內壁平整,焊縫強度須不小于鋁套強度,不得有明顯突起,不允許有圓周方向的焊縫。


4.2.8 瀝青涂層

瀝青涂層就是金屬套表面的瀝青或熱熔膠防蝕層。防腐層附著性好,被均勻、完整地涂覆在金屬套上;


4.2.9 非金屬外護套

外護套分為單層外護套和雙層外護套。采用單層護套結構時,應采用高密度聚乙烯(HDPE)、聚氯乙烯(PVC)材料 。外護套具有良好的防腐蝕、防蟻、防潮和阻燃性能;敷設于隧道內電纜非金屬外護套應采用低煙低鹵阻燃料,外護套表面都有不易脫落的連續性完好的導電層。

外護套需增加“退滅蟲”(“Termigon”)或“退敵蟲”防蟻護層時,采用雙層護套結構,其中內層護套應采用高密度聚乙烯(HDPE)護套料,外層護套應采用“退滅蟲”(“Termigon”) 或“退敵蟲”防蟻護套料。

內層高密度聚乙烯護套厚度應為3.03.5mm,外層防蟻護套厚度應為2.0±0.1mm。內層高密度聚乙烯宜選用紅色添加劑,以示和外層防蟻護套區別。防蟻護套具有良好的抗腐蝕性(尤其是螞蟻分泌的甲酸)、耐磨性和彈性。表面具有較高的光潔度。


4.2.10 石墨半導電層

位于外護套表面有一層以石墨半導電層,半導電層均勻地包覆在外護套上。牢固的導電層作為外護套耐壓試驗時的外電極。


五、吊裝、貯存、運輸

5.1吊裝電纜應用滿足重量要求的起重機及鋼纜吊裝,嚴禁幾盤同時吊裝,嚴禁從高處扔下裝有電纜的電纜盤,嚴禁機械損傷電纜,吊裝時不得磕碰、吊斜,起吊點要正確,要輕吊輕放。

5.2  電纜盤不允許平放或溜放,電纜附件應避免在露天存放,電纜及附件應避免接觸有腐蝕性的物質,應采取必要的防火措施。并有專人經常巡視,防止因意外情況造成電纜及附件受到損傷。

5.3  裝在車、船等運輸工具上的電纜盤必須平穩放置,采用合適方法固定(如線盤托),防止互相碰撞或翻倒。

5.4  電纜盤(不論有無托架)放置的位置要平整,不得存放于大于5度的斜面上。電纜盤側板上標有“電纜盤滾動方向”和“牽引頭拉出方向”,牽引頭拉出方向與放線方向一致,放線前,應確認無誤。

(銷售中心)?(Tender Quatation)?(銷售業務對接)
 工作時間
周一至周五 :8:30-17:30
周六至周六 :9:00-12:00
 聯系方式
客戶經理Customer Manager:郭經理
手機號碼 Mobile:13580489721(微信同號);18928822020
電話號碼Tel:86-020-82986388-8153
傳真號碼  Fax:86-020-82986949
Web郵箱( E-mail):gznycables@163.com
客服郵箱 service E-mail:1091415526@qq.com
聯系地址(總部):廣州經濟技術開發區永和經濟區永豐路19號-廣州南洋電纜集團有限公司
Headquarter Address:No. 19 Yongfeng Road, Yonghe Economic Zone, Guangzhou economic and Technological Development Zone

網站內容均受?chē)曳杉皣H公約有關著作權、商標權、專利權及其他財產所有權法律保護,為m.nonprofitgallery.com網站專屬。未經投標報價中心網站管理人明確書面授權,任何人不得變更、轉載、復制、改動、散布任何內容,否則以侵權論,依法追究法律責任。


因為專注 所以專業

Dedicated    and    professional

廣州南洋電纜集團有限公司


(銷售中心)

(Tender Quatation) Sales center

會(huì )員登錄
登錄
其他賬號登錄:
我的資料
留言
回到頂部